PLUMBING FOR BEGINNERS: THE ESSENTIALS FOR INSTALLING A BATHTUB

Plumbing for Beginners: The Essentials for Installing a Bathtub

Plumbing for Beginners: The Essentials for Installing a Bathtub

Blog Article

Website

This article down below involving A Step-by-Step Guide to Installing a Bathtub is immensely captivating. Give it a go and make your own personal findings.


How to Install a Bathtub Yourself
Mounting a tub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a new one is likewise a moderately tough job. If the old bathtub is readily available, the task can move speedily; if you need to open up a wall to get rid of the old tub and also position the new tub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will require a helper to vacate the old bathtub and also set in the new one. Make certain you have actually qualified on your own for the task as well as fit trying it. Rather than hiring a professional to take over a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This short article will certainly assist you set up a new tub in your bathroom if you have actually currently bought a new tub as well as do not require to transform the arrangement of your previous water system pipelines.
Your devices and also product list need to consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of removing the existing taps can be quite bothersome due to the limited accessibility that is usually the situation.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
    Prior to carrying on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the existent supply pipes.
    If you require to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next, position the tap in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet as well as the sink. Secure the faucet in place with the producer provided backnut. Once the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous kind should be connected to the faucet finishes initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Installing the Tub


    Using the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four small factors.
    The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the spirit level as well as adjusting the feet on the bathtub till the level checks out degree.
    To install faucets, fit the bottom of the furthest versatile tap connector to the suitable supply pipe by making a compression join; after that do the very same for the other tap.
    Turn on the water and also check all joints and also new pipework for leakages and tighten them if required. Fill up the bath tub and also check the overflow outlet as well as the normal electrical outlet for leaks.
    Ultimately, take care of the bath paneling as explained in the maker's instruction manual. Tiling and sealing around the tub ought to wait until the bath tub has been made use of a minimum of once as this will resolve it right into its final placement.

    Preparing for the Installment


    To start with, the supporting framework supplied with the bath should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to ensure that if the tap includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop stress on the tub.
    Fit the flexible faucet ports to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the provided washing machines.
    Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last setting.

    Tiling Around the Bathtub


    In the location where the bathroom satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a stiff seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, causing complications with dampness and also possible leaks to the ceiling below.
    You can select from a range of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched paper or soft rope. Remember to always fill up the tub with water prior to sealing, to permit the motion experienced when the tub is in usage. The sealant can crack rather early if you do not take into account this activity prior to securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily available on the market. It is suggested to fit the ceramic tiles making use of waterproof or water-proof sticky as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Installing A Bathtub

    As a keen person who reads on How to Install a Bathtub Yourself, I was thinking sharing that piece was really useful. Those who appreciated our page plz do not forget to pass it around. Thank you for your time spent reading it.


    Ready when you are!

    Report this page